Expert EX-9132-2 Spezifikationen

Operation Manual of EX-9132C-2 DDS Serial to TCP/IP Converter Version 1.1.0 , 25th Jan. 2010

9 RS-422 Signals：Rx+ , Rx- , Tx+ , Tx- (Surge & Over Current Protect)  RS-485 Signals : Data+ , Data- (Surge & Over Current Protection)

1022 EX-9132C-2 Description & Installation Product Panel Views Top Side Right Side Serial I/O Port of RS-232 and RS-232/422/485 Connect the s

11Digital I/O Through EX-9132C-2 , D I/O can transform the status of sensor into the TCP/IP package data and send out by Ethernet Data Stream (The E

12Left Side Power Supply EX-9132C-2 TCP/IP converter device is powered by a single 9VDC (inner positive/outer negative) power supply and 500mA of cu

13LED Indicators PWR (Red): It is a power indicator (When the power is on, the LED will be on.) Tx (Green): Data transmitting indicator (When data

14Wiring Architecture RS-232 Wiring Architecture RS-422/RS-485 Wiring Architecture

15When you finish the steps mentioned above and the LED indicators are as shown in above diagram, the converter is installed correctly. You can u

1633 EX-9132C-2 Converter Configuration Initial IP Configuration When sett up your converter for the first time, the first thing you should do i

17When you activate the tool, it will detect the existence of the installed converters and depict the converters’ status such as IP address, Subnet

18EXBrowser “View” □□□ View -> Refresh There are two ways for refreshing the status of existing devices. You may select the item “View” to refre

1 Table of Contents 1. Introduction ……………………………………………… 3 Overview ……………………………………………………… 4 Package Checklist ……………………………………………… 4 Block Diagr

19 (Figure 3.4) Assign an IP Address with the same Subnet Mask of your computer, avoiding any IP conflict with other network devices. When you pre

20 EXBrowser “Modify MAC” □□□ Modify MAC -> Dialog Frame To click the device on the existing devices list in the EXBrowser table and then the

21Web Browser Configuration The following topics are covered in this chapter: □□□ Serial To Ethernet Converter Setup ● Login Setting ● Login Set

22of browsers. (Figure 3.9) Login Setting Page Field Description □□□ System time elapsed The time elapsed since start of this device in [Day Ho

23 □□□ Ethernet MAC Address Converter is a unique MAC (Media Access Control) address used by Ethernet. □□□ Password This field is the administr

24Parameter Setting Page □□□ The Parameter Setting Page Type the correct password in the “Password” field and click the “Confirm” button in the “

25□□□ Parameter Setting Page Field Description □□□ IP Address The IP address of converter device, 4 digits separated by '.' Don’t let

26 □□□ Device ID Report You may “Enable” or “Disable” to collect the device ID report and assigne ID number for the converter devices. Available ID

27The server IP address and socket port would be connected in TCP Server, TCP Client and UDP Client mode for a certain serial port. □□□ Remote soc

28A socket port is assigned for the serial port. It’s a 16-bit numbers, ranging from 1 to 65535. Because the numbers below 1000 are used for specif

24. EX-9132C-2 Configuration ...……… 16 Initial IP Configuration ...……………………………………… 16 Device Management Utility of

29□□□ Interface of serial I/O  RS-232: TxD, RxD for data stream, no flow control  RS-232 (RTS/CTS): TxD, RxD for data stream, RTS/CTS for flow

30Controller Updated Press “Update”] Button after finish the detailed parameter setting. The converter will save all parameters into internal non-v

31Factory Default Setting If you forget the setup password or have incorrect settings making the converter inoperable, there are two ways to reset

321. 55 Setting Verification After complete the wiring and parameter setting, we should verify if the setting is correct. This chapter will in

33Hyper Terminal for TCP/IP WinSock Initiate a Hyper Terminal from the Start Menu in Windows (see Figure 6.1), give a terminal name, choose an icon

34 (Figure 6.2) Select “TCP/IP (Winsock)” option at the “Connect using:” field (see Figure 6.3).

35 (Figure 6.3) After “OK” button is pressed, Figure 6.4 appears. Enter the converter’s IP address (e.g. 192.168.123.10) at the “Host address:”

36 (Figure 6.4) After “OK” button is pressed, Figure 6.5 appears. If the Hyper Terminal connects with the converter successfully, the time clock at

37 (Figure 6.5)

38Hyper Terminal for COM Port Initiate another Hyper Terminal as a COM Port Terminal (in Figure 6.3, select COM 1 or other COM port instead of “TCP

3 11 Introduction We provide new ways of connecting legacy serial devices to a Local Area Network (LAN) or Wide Area Network (WAN). TCP/IP conver

39Data Transmission When all steps described above are finished, type any texts on the COM Port Terminal and check if the texts are also displayed

40AAppppeennddiixx AA FAQ Q. Why can’t the EXBrowser.exe detect the converter on the network? A. Please check □□□ if the power is properly

41AAppppeennddiixx BB Pin outs and Cable Wiring □□□ DC-In Jack □□□ RJ-45 Pin Assignment □□□ RS-232 Pin Assignment The pin assignment sc

42□□□ RS-232 Wiring Diagram Serial Device EX-9132C-2 2 RX 3 TX 3 TX

4Overview EX-9132C-2 converter is designed to make your industrial serial devices Internet ready instantly. ARM Cortex-M3 CPU of EX-9132C-2 converte

5Block Diagram Low-cost devices usually are equipped with low speed processors and limited memories. In reality, they have neither the capability

6The central core of ARM Cortex-M3 processor, based on a 3-stage pipeline Harvard bus architecture, incorporates advanced features including single

7 Product Features □□□ Data Conversion between RS-232 and RS-422/485 and Ethernet EX-9132C-2 converter device (RS-232＊1 port , RS-232/422⁄485＊1 po

8Product Specifications  CPU : ARM Cortex™-M3 32-bit processor , 50MHz  RAM : 64K Bytes SRAM  ROM : 256K Bytes Flash ROM  Ethernet ● Port T